Burcam 300828 CAST IRON SUBM. SUMP PUMP VERTICAL SWITCH 1 Bedienungsanleitung PDF herunterladen

2190 Dagenais Blvd. West TEL: 514.337.4415

LAVAL (QUEBEC) FAX: 514.337.4029

CANADA

H7L 5X9 [email protected]

INSTALLATION

INSTRUCTIONS

Your pump has been carefully packaged at the factory to

prevent damage during shipping. However, occasional

damage may occur due to rough handling. Carefully inspect

your pump for damages that could cause failures. Report any

damage to your carrier or your point of purchase.

WWW.BURCAM.COM

MODEL

300828

SUBMERSIBLE

SUMP PUMP

Please read these

instructions

carefully. Failure

to comply to

instructions and

designed

operation of

this system,

may void

the warranty.

MONTHL

Y MANDA

TORY CHECK-UP:

1. Inspect the pump and the sump for any

obvious condition that necessitates cleaning,

correction, adjustement or repair.

2. Clear the sump and the surroundings of

any paper, leaves or other debris that might

clog the input openings. Remove anything

that might float into the sump.

3. Assure that the pump is secure and

vertical for proper operation.

4. Assure that there is adequate clearance

from any combustible materials or structure.

Stored materials must be kept away from the

pump. Shelves or cabinet structures must

not be in close proximity over the pump.

5. Assure that the motor is securely plugged

into a proper GFCI electrical outlet.

6. Test the ‘GFCI’ outlet by pressing its test

switch. This should prove that the outlet is

energized and will trip off to protect against a

ground fault. Be sure to reset the ‘GFCI’ by

pressing its reset switch.

7. Lift the float to prove that the pump will

start when required. (Step 8 below will test

submersible pumps with enclosed floats).

8. Put a pail of water (8 liters) in the sump to

prove that any check valve present will

permit effluent to flow.

9. Observe that the plumbing can carry the

effluent safely out of the residence.

1 2 3 4 5 6

Inhaltsverzeichnis

Seite 1 - INSTRUCTIONS

Seite 2 - SAFETY INSTRUCTIONS:

SAFETY INSTRUCTIONS:This fine pump that you have just purchased is designed from the latest in material and workmanship. Before installation and opera

Seite 3 - INSTALLATION STEPS

3APPLICATIONThis submersible sump pump is designed for apermanent sump installation.To be used in a residential cottage and farm application.CAP

Seite 4 - SUMP PUMP APPLICATION

4At this step, you have the opportunity to install a 1 1/2” or a 1 1/4” discharge. We recommenda 1 1/2” ABS/DWV discharge. Install a check valve (350

Seite 5 - REPAIR PARTS

REPAIR PARTSSTEP 2Sump pit 18” diameter X25” depthSTEP 3Determine your choiceof discharge pipe sizeand check valveSTEP 4Install your pump incentre of

Seite 6

6TROUBLE SHOOTING GUIDE CHECKLISTNEVER MAKE ADJUSTMENTS TO ANY ELECTRICAL APPLIANCE OR PRODUCT WITH THE POWERCONNECTED. DON’T JUST UNSCREW THE FUSE OR

Kommentare zu diesen Handbüchern

Keine Kommentare

Burcam 300828 CAST IRON SUBM. SUMP PUMP VERTICAL SWITCH 1 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Pumpen Burcam 300828 CAST IRON SUBM. SUMP PUMP VERTICAL SWITCH 1 herunter. Burcam 300828 CAST IRON SUBM. SUMP PUMP VERTICAL SWITCH 1/3HP 115V User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Pumpen Burcam 300828 CAST IRON SUBM. SUMP PUMP VERTICAL SWITCH 1